 warranty
2-AMP DC VARIABLE OUTPUT POWER SUPPLY
FOR SALE
Great for general purpose bench work. Supplies enough current to power
most DC
devices for short of long term use. Supplies 3, 4.5, 6, 9, and 12 volts
very accurately
and is completely filtered as is shown on the oscilloscope output. All
voltages test to
rated specs. We also un-box and bench check each unit prior to shipping to
absolutely ensure
performance upon delivery. Output is via heavy duty binding / banana
posts. Each unit is fused
for protection. This is one of the most useful and high quality power
supplies we have found and
it's very affordable!
NEW AND IN STOCK!
$28.99
|
NEW ADDITION
1/15/08
(click on above thumbnails to enlarge photos)
10-AMP Vari-AC
PROJECTOR SPEED ADJUSTER
for sale
Inexpensive Variable AC power supply for general
bench work. Many uses. We use ours almost daily for bringing up tube gear
after a cap job, or to bring up a radio or amplifier that has "sat" for an
undetermined period of time. Also great for finding under-power / over-power
issues in gear.
Also,
good for varying the speed of motors or the brightness of lamps as long as
max current limits and low voltage limits are not exceeded. *Motors should
generally not be ran with very low voltage, so user should use
common sense and listen to the motor for low limits. Running a motor at
voltages that are too low can and eventually will destroy the motor and create potential
an over heating / fire hazard. When used properly, it should not be
necessary to approach the lower voltage limits anyway. Conversely, while the
transformer will allow up to 130 VAC, it is not recommended to exceed the
120 Volt setting. This also could create an overheating issue and seriously
reduce motor and lamp life. When using a Vari-AC / Variable AC power suppy, it's limitations need to always be understood and
considered. Some knowledge of electronic principles will be useful.*
Specs:
- Varies
line voltage between 0~130VAC.
- Built-in ammeter shows current draw
-Replaceable fuse protection
- Three prong grounded cord and socket provides
convenience and safety
- Specifications120V, 60Hz Output
0~130VAC Current10A, 1.3KVA 10A AGC
NEW
$199.99
*Again,
Vari-AC's can have many uses. Varying the speed of a motor, bringing voltage
up slowly on gear for trouble-shooting, getting "brown AC" to guitar tube
amps, and controlling the
brightness of a lamp are only a few. It is a tool. Tools are designed for many
"known uses", but in the hands of qualified personnel, can be used for other
"non-designed" uses. Improperly used, this "tool" can be dangerous, both to
the operator and to the equipment. No warranties are expressed or implied.
If you do not understand the use of a Vari-AC, DO NOT
PURCHASE FOR USE, OR USE ONE!
|
(Click on above thumbnails to
enlarge photos)
RCA
MODEL WV-76A
AC VTVM
FOR SALE
Serial # 1057
needs probe(s). Untested, but does power up and meter responds. Not tested
beyond that. Appears
cosmetically in
good cond. Meter
window slightly
scuffed, no cracks. Overall cosmetic cond. 7.5
$45.
|
(Click on above thumbnails to
enlarge photos)
SENCOR
TRC-4
Transistor checker
FOR SALE
Unopened crack in VU window visible in photo. Seems to work. Battery
powered. No manual.
Cond. 7
$39.
|
NEW LISTING
(Click on above thumbnails to
enlarge photos)
B&K
960
#603677
TRANSISTOR RADIO ANALYST
FOR SALE
These are great "all-in-one"
units, however this one needs restoration or use for parts. Will need tubes
at least. When the two tubes were installed, the tone generator worked at
3.1kHz. The tubes are not included.
Cond. 5
As-Is
$39.
|
(Click on above thumbnails to
enlarge photos)
SOLA
CVT
MODEL 63-13-114
Constant Voltage Transformer
AC Line Power Conditioner
FOR SALE
Designed to hold a constant voltage output of 120 VAC +
within a range of input voltages. It is designed for use between 95-130 VAC. We input a
variety of voltages with the following results:
Input:
Output:
30 V =
112V
50 V =
116V
60 V =
118V
80 V =
121V
100 V =
123V
115 V =
125V
125V =
126V
It is rated for a maximum current of 1.17amps. Unit in very good condition and works
great! Measures 14" X 5.5" X 5.5" and weighs 18lbs.
Cond. 9
$59.
|
(Click on above thumbnails to
enlarge photos)
VARIAC
SUPERIOR ELECTRIC CO.
MODEL S649
"POWERSTAT"
FOR SALE
Accepts 110 or 220 AC volts
input. 9 amp capacity. 10-140 volts output with 110 volts input. Great for
general bench work, reforming and breaking in filter caps, troubleshooting
tube amps by lowering or increasing their voltage, or dimming lighting. Also
could be used to run a tube amp "brown" if you so desire. Very
heavy duty, older USA made unit. Much more durable than most of the import
units. Very well ventilated. Can be mounted to a panel from the inside, or
left free-standing. Output bolts are 1/4". Shaft should have knob
installed. It's diameter is 3/4", and it protrudes 1 1/4" from the
front. Unit diameter is 8" at it's widest point, and 7" tall not
counting the shaft. The variac weighs 26 lbs.
Warning:
Due to high potential AC current and voltage, Vari-AC's are very dangerous
for the untrained user. Only for use by qualified technicians!
COND. 8.5
$129.
|
(Click on above thumbnails to
enlarge photos)
Todd
Step-down Transformer
FOR
SALE
Converts up to 220 volts into half voltage. Has standard Edison plug and jack, but could
be converted to anything.
$45.
|
(Click on above thumbnails to
enlarge photos)
warranty
ELECTRO-TECHNIC
5000
VARIABLE AC / DC POWER SUPPLY
FOR SALE
Nice general purpose, bench-top variable power supply. Variable 0-11 volts
(tested to 13 volts) AC output and 0-6.5 (tested to 16volts)
DC output at 4.5 amps via binding / banana posts. Unit tests great.
Measures 7" wide x 4.5" deep x 5" tall and weighs only5
lbs. Includes our standard 90 day limited warranty.
Cond. 9
$55.
|
(Click on above thumbnails to
enlarge photos)
DUAL 3.6 (4 OHM)
210 WATTS EACH
DUMMY LOADS
FOR SALE
IRC Brand
very good
quality older USA made resistors. These are new old stock. Perfect for
loading tube amps. Could be the heart of a versatile dummy load box. They
could be configured for 2, 4, or 8 ohms of load. Measure 1" in
diameter, and are 10.5" long.
COND. 10
$40. pr.
ON HOLD FOR SHOP USE
|
(Click on above thumbnails to
enlarge photos)
PLATT
Diced-Foam
Utility Case
Model 2005
FOR SALE
Medium-Duty ABS utility case filled with Diced foam and a finger foam
lined lid. NEW! Includes keys and catalog. Slight depression to front edge
along handle. Does not affect performance. Measures inside 20" wide x
14" front-back x ~6" high / deep. Weighs 7 lbs loaded with foam.
Cond. 9.5
$59. 1 only |
NEW LISTING 1/24/06
(Click on above thumbnails to
enlarge photos)
HP 150A
Oscilloscope
w/152B
DUAL TRACE AMPLIFIER
MODULE
"AS-IS"
FOR SALE
This unit is an impressive piece of
test gear. In its current condition however, it is only suitable as a
theatrical prop, display or as a hobbyists, "fixer-upper". The tubes are
gone and only the most perfunctory of testing has been performed to see
which lights, light. (see above photos). The 152B Dual Trace Amplifier
module is removable and other modules can be inserted for differing
functionality.
Measures 6.5" wide x 8" tall and 4.5" deep. Selling As-Is for fix-up or
for parts.
HP 150A w/152A module
Cond.
AS-IS
$150.
|
NEW LISTING 1/24/06
(Click on above thumbnails to
enlarge photos)
HP 151B
Oscilloscope
HIGH GAIN AMPLIFIER
MODULE
"AS-IS"
FOR SALE
This HP-151A, High Gain Amplifier,
module is a companion module for the HP 150A Oscilloscope. Suitable for
display use or for a fix-up. Functionality unknown as all the tubes are
pulled and not included.
Measures 6.5" wide x 8" tall and 4.5" deep. Selling As-Is for fix-up or
for parts.
HP 151B
Cond.
AS-IS
$40.
|
NEW LISTING 1/24/06
(Click on above thumbnails to
enlarge photos)
HP 154A
Oscilloscope
VOLTAGE / CURRENT AMPLIFIER MODULE
"AS-IS"
FOR SALE
This HP-154A, Voltage / Current
Amplifier, module is a companion module for the HP 150A Oscilloscope.
Suitable for display use or for a fix-up. Functionality unknown as all the
tubes are pulled and not included.
Measures 6.5" wide x 8" tall and 4.5" deep. Selling As-Is for fix-up or
for parts.
HP 154A
Cond.
AS-IS
$40.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
-
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
BELOW ITEMS ARE SOLD
|
BELOW ITEMS ARE SOLD
|
BELOW ITEMS ARE SOLD
|
| |
|
(Click on above thumbnails to enlarge photos)
TEAC TASCAM
TO-122A TEST TONE OSCILLATOR
for sale
Also great for injecting signal into amps and mixing board!
I used these Teac TO-122A Test Tone generators for years in the field as a
Tascam dealer. I always had one in my tool box for testing Pro-Audio sound
systems in clubs and churches. I used them to detect signal paths and look
for anomalies in room acoustics at different frequencies. They're also great
for setting levels on input gains and for leveling power meters. They have
many other uses as well. Small package runs off a standard 9-volt battery.
Fixed 1/4" out. Frequencies are selectable 40Hz, 400Hz, 1kHz, 4kHz, 10kHz
and 15kHz. Levels are selectable between -10 or -40dB. Unit works perfectly
and looks great. LED to show power on. Easy 2-screw battery change if you
accidentally leave it on or just need to change the battery. Unit is small
enough to fit in your tool box measuring only 3 1/8" wide x 2.5" deep x 1.5
tall. These are no longer available from Teac new.
Teac TO-122A
SOLD
|
NEW LISTING
(Click on above thumbnails to enlarge photos)
warranty
RCA
WV-98C
"SENIOR VOLT-OHMYST"
VACUUM TUBE VTVM
MULTI-METER
FOR SALE
Classic tube volt / ohm meter found on most test / work benches. We have
completely gone through this one, checking / replacing the internal tubes, caps and
installing a new D cell. We have calibrated to manual
specs. Tests accurately with our calibrated bench unit and work great! Looks near new. No
cracks in window or rust. All original knobs. Comes with original RCA
WG-299E probe with selectable AC or DC resistance. Original leather handle
in perfect condition. Includes a copy of the owners /
users manual. Measures 7" wide x 6.5" tall and 4.5"
deep. Includes our standard 90 day warranty (excluding blowing it up by
injecting voltage when in Ohms position).
Cond. 8.5
$169.
SOLD 10/25/06
|
NEW
LISTING
(Click on above thumbnails to enlarge photos)
warranty
TRIPLETT
310
MULTI-METER
HOLD SHOP USE 11/28/07
Circa 1963
UNDER CONSTRUCTION
UNDER CONSTRUCTION
UNDER CONSTRUCTION
FOR SALE
New, unused condition. No cracks in window
or rust. All original knobs. Original case in
new condition. Includes a copy
of the owners / users manual. Measures
7" wide x 6.5" tall and 4.5"
deep.
Cond. 10
HOLD SHOP USE 11/28/07
|
NEW LISTING
(Click on above thumbnails to enlarge photos)
warranty
TRIPLETT
630-PL MULTI-METER
HOLD SHOP USE 11/28/07
Circa 1963
UNDER CONSTRUCTION
UNDER CONSTRUCTION
UNDER CONSTRUCTION
FOR SALE
New, unused condition. No
cracks in window or rust. All original knobs. Comes with original,
un-used probes. Original leather handle
and case in new condition.
Includes a copy of the owners / users manual. Measures
7" wide x 6.5" tall and 4.5"
deep.
Cond. 10
HOLD SHOP USE 11/28/07 |
(Click on above thumbnails to
enlarge photos)
warranty
RCA
WV-97A
SOLD 4/7/06
"SENIOR VOLT-OHMYST"
Vacuum tube VTVM multi-meter
FOR SALE
Classic tube volt / ohm meter found on most test / work benches. However
we can't seem to get this one to zero. We checked the tubes inside and
installed a new Cap, AC cord and cleaned contacts and controls, but didn't
investigate too far. No
cracks in window or rust. All original knobs. Original leather handle
in perfect condition. Measures 6.5" wide x 8" tall and 4.5"
deep. Selling As-Is for fix-up or for parts.
$35.
SOLD 4/7/06
|
NEW LISTING
(Click on above thumbnails to
enlarge photos)
EICO
MODEL 324
RF GENERATOR
SOLD 2/23/07
FOR
SALE
Classic RF generator for general Radio
Audio / Stereo repair. These have been found on service benches for years.
Features include:
- 6 Tuning bands
- 175 kc - 475 mc range
- 6 to 1 Vernier Tuning Dial with back light
- Built-in 400 Hz audio tone generator
- External modulation tone input
- Course and fine Attenuators
- Accuracy of tuning dial indicators +- 1.5%
- AF output voltage 0-10 volts across 100k ohms and 0-5 volts across 10k
ohms
- AF input impedance 70k Ohms
- AF output impedance 10k Ohms
- External Modulation freq range 20-15,000 Hz
- Internal tubes 1x 12AU7 and 1x 12AV7
These are great for aligning AM and FM tuners and
tuning sections on Hi-Fi gear. Also function as small radio transmitters.
Fun for creating a mini broadcast station in your house / lab. This one does
need some work. It does produce some output and does have AF output, but is
not correct. We are selling it as is. Unit does look good and is clean
inside. Likely a minor problem, but we do not have time to chase it, as we
have a working one on our test bench. Unit measures 10" wide x 8" tall x
4.75" deep and weighs 10 lbs unpacked.
Cosmetic cond. 8.5
As-Is
$55.
SOLD 2/23/07 |
(Click on above thumbnails to enlarge photos)
TAU-TRON
S5104
DIGITAL
TRANSMISSION TEST SET
SOLD 3/9/07
FOR SALE
I know a little about a lot of different stuff
and a lot about a few things, but virtually nothing about Transmission
Test Sets. We have had a couple in the past that have sold, but that's all
I know. Unit fires up and does respond to it's switches. The last
one we had could do a "self-test", but I don't know how to
engage a test with this unit. According to some other info on the web it's
used for testing digital radio, fiber-optic and T-carrier systems
including multi-plexers, switches and lines. Has GPIB and RS 232 outputs.?
Sorry no manual with it. Measures 13.5" wide x 17.5" deep x
7" tall (with stand folded in) and weighs 20 lbs unpacked. AC cord
included.
Selling As-Is
Cosmetic Cond. 8.5
$159.
SOLD 3/9/07
|
(Click on above thumbnails to enlarge photos)
AMERITEC
AM5XT
VOICE/DATA TRANSMISSION TEST SET
SOLD 3/9/07
FOR SALE
I know a little about a lot of different stuff
and a lot about a few things, but virtually nothing about Transmission
Test Sets. We have had a couple in the past that have sold, but that's all
I know. Unit fires up and does respond to it's switches. The last
one we had could do a "self-test", but I don't know how to
engage a test with this unit. According to some other info on the web:
"The Ameritec AM5eXT-200 Wideband Transmission
Test Set is specifically engineered for peak performance for use in the
field and in the lab. This easy-to-use unit offers a full range of
transmission impairment measurements and a highly versatile signal generator
in a single, compact, portable instrument. Approximately the size of a
telephone directory, this test instrument fits conveniently on a bench top
for use as a laboratory unit. It can also be rack mounted."
"Portable
wideband transmission impairment set with sweep function that can be
programmed to automatically perform tests across the 20 kH to 200 kHz
bandwidth, while simultaneously measuring level and frequency across the
same bandwidth."
"100% digital control of all measure, filter,
send, and termination functions"
"Front panel with easy-to-locate and easy-to-read
areas for each of the major instrument functions."
"Together with the optional internal rechargeable
battery pack and soft carrying case, the AM5eXT-200 can be used as a field
tester with a battery life of up to six hours of uninterrupted use."
"Performs qualification tests on circuits carrying
voice band, high quality audio, and basic rate ISDN and HDSL or other
services using up to 200 kHz bandwidth."
"Simultaneously sends signal and measure received
signals."
"Provides individual selection of "send and
receive terminations" and "on hook/off hook DC hold" circuits."
Testing capabilities include dBm level or dB loss,
frequency, frequency response (attenuation distortion), noise (wideband or
with filters), noise with tone (wideband or with filters), signal-to-noise
ratio (wideband or with filters), noise to ground (wideband or with
filters), impulse noise (wideband or with filters), phase jitter, amplitude
jitter, micro interruptions, group delay, inter-modulation distortion
(4-tone/2-tone), 2- and 4-wire return loss, and transients (including phase
and gain hits as well as impulse noise with tone and interruptions)."
"Sophisticated test scripts can be obtained by
simply drawing the test sequence. Call scripts are easily developed by
dragging, dropping, and interconnecting icons to create a graphical call
flow diagram."
Sorry no manual with it. Measures 8"
wide 12" deep 4" tall (with stand folded in) and weighs
7 lbs unpacked. AC cord
included.
Selling As-Is
Cosmetic Cond. 8.5
$299.
SOLD 3/9/07
|
NEW
LISTING 3/16/06
(Click on above thumbnails to enlarge photos)
SIMPSON
360
MULTI-METER
Circa 1963
SOLD 4/7/06
|
(Click on above thumbnails to
enlarge photos)
OHMITE
VARIABLE 0-25 OHM /
500 WATT
HOLD FOR SHOP USE
DUMMY LOAD / RHEOSTAT
RATED TO 4.47 AMPS
FOR SALE
This is the same model we use on our test bench for testing amplifier
outputs. Can be marked at 2, 4, 8 & 16 ohms for convenience or any
setting from 0-25 ohms. Wattage capacity is 4.47 amps / 500 watts. Can be used as-is or mounted behind a panel.
Mounting flange included. Great condition. Measures 7.5" in diameter
and is 2" thick. Very handy test load. Great speaker substitute. Made
in USA.
1 only available @
$129.
HOLD FOR SHOP USE
|
(Click on above thumbnails to
enlarge photos)
NRI
MODEL 2500
SOLD 9/15/05
5-Mhz
OSCILLOSCOPE
Oscilloscope
Works well. Single
trace, 5 Megahertz. Very clean. Great scope if you need something simple
that doesn't take up much space on your bench. Probe not
included, but is standard BNC connection.
Rule leaning against side is 6".
COND. 9.0
$110.
SOLD 9/15/05
|
(Click on above thumbnails to
enlarge photos)
warranty
FLUKE
1900A
SOLD 8/20/05
FREQUENCY / MULTI-COUNTER
FOR SALE
Multi-Counter. Provides frequency, period, period averaging, and totaling
of measurements. Frequency range 5 Hz to 80 MHz. Looks and works great. All
functions seem to check fine. May need a slight calibration, but was very
close to our bench unit. Just need a BNC cable for input. Sorry no manual
with it. Includes our standard 90 day limited warranty.
Cond. 8.5
$59.
SOLD 8/20/05
|
(Click on above thumbnails to
enlarge photos)
200 in ONE
SOLD 11/15/05
ELECTRONICS PROJECT / EXPERIMENTERS KIT
FOR SALE
Great kit for beginning experimenters and advanced students alike. Parts
fixed in place and includes lots of jumpers to connect solderless
junctions. Learn basics of electricity and electronics. Lots of projects
to build from amplifiers to oscillators to an AM radio and broadcaster to
computer circuits and many more. Includes meter, pots, switches, speaker,
transformers, relay, antenna and more! Also includes original box and 109
page instruction / project manual. Uses 6 AA-batteries (not included).
$39.
SOLD 11/15/05
|
NEW LISTING 7/15/05
(Click on above thumbnails to
enlarge photos)
ACCURATE INSTRUMENT CO.
MODEL 151
SOLD 8/5/05
TUBE TESTER / CHECKER
FOR
SALE
Great little, solid state, emission type
tube tester from Accurate Instrument Company. Small and light. Very simple
to operate. Great for intermediate shop / hobbyist. Tests for shorts,
leakage and quality of emission. Great for Radio / Audio work. We have
completely cleaned all the switches and pots. We tested the following tubes
consistently with our calibrated, shop B&K 747B tester (12AU7, 12AT7, 12AX7,
6L6, 6V6, 6BQ5 / EL84 & 6W4). Has built-in tube pin straightener. Comes with
copy of original manual / tube chart / schematic. Works great and looks near
new. It is ready to go.
Unit measures 10.5" wide x 3.5" tall (closed) x 9"
deep and weighs 5 lbs unpacked.
Cosmetic cond. 9
As-Is
$139.
SOLD 8/5/05
|
NEW LISTING 7/15/05
(Click on above thumbnails to
enlarge photos)
PACO
MODEL G-30
SOLD 8/20/05
RF GENERATOR
FOR
SALE
Very good condition
and did pass pre-testing to as far as our Frequency counter would test
(3.9mHz), RF generator for general Radio
Audio / Stereo repair. A Paco G-30.
Features include:
- 6.5 Tuning bands
- 158 kc - 240 mc range
- Vernier Tuning Dial
- Built-in 400 Hz audio tone generator
- Variable AF output level control
- External modulation tone input
- RF Output and Level Attenuators
- 2 Internal tubes
These are great for aligning AM and FM tuners and
tuning sections on Hi-Fi gear. Also function as small radio transmitters.
Fun for creating a mini broadcast station in your house / lab. This one does
need some work. Unit does look good and is clean
inside. While we did not do a full restoration on this unit, it does appear
to work well. Should be completely gone through and calibrated, prior to use. Unit measures 11.5" wide x 8" tall x
6" deep and weighs 10 lbs unpacked.
Cosmetic cond. 9
As-Is
$85.
SOLD 8/20/05
|
(Click on above thumbnails to
enlarge photos)
HEATHKIT
MODEL 10-104
SOLD 6/3/05
OSCILLOSCOPE
FOR
SALE
Nice 5-Megahertz single trace O-Scope. Great for general audio bench work.
This has been our old stand-by for a few years, but it looks like the
smaller scope we have now is going to work better for us. This scope is in
great shape and everything works well. No burns on screen! If you have
space and don't need tons of features then here you go. A good reliable
scope for beginners and pros alike. Measures 10 3/4" wide x
20.5" deep x 12.5" tall and weighs 33 lbs unpacked. Utilizes
standard BNC connector probe (none included)
Cond. 8.5
$99.
SOLD 6/3/05
|
(CLICK ABOVE PHOTOS TO ENLARGE)
warranty
RCA
WV-98C
SOLD
"SENIOR VOLT-OHMYST"
Vacuum tube VTVM multi-meter
FOR SALE
Classic tube volt / ohm meter found on most test / work benches. We have
completely gone through this one, checking the internal tubes, caps and
installing a new D cell. Seems to test and work great! Looks near new. No
cracks in window or rust. All original knobs. Comes with original RCA
WG-299E probe with selectable AC or DC resistance. Original leather handle
in perfect condition. Measures 7" wide x 6.5" tall and 4.5"
deep. Includes our standard 90 day warranty (excluding blowing it up by
injecting voltage when in Ohms position).
Cond. 8.5
SOLD
|
(CLICK ABOVE PHOTOS TO ENLARGE)
B&K
650
SOLD
#200005
DYNAMIC MUTUAL CONDUCTANCE
TUBE / TRANSISTOR TESTER
FOR SALE
Will test both tubes and transistors. Good
for simple, easy, and quick tests without flipping a lot of switches.
All internal components checked. Comes with 75% complete tube chart
(cards), but info for most tests is silk screened next to each tube
socket. Seems
to work well. Tested sample tubes 5U4, 12AX7, 6SJ7, 35W4, 6V6,
And 6L6 consistent with our calibrated shop B&K 747B. Again
we do not have a complete tube chart or manual. Case worn.
COND. 6.5
SOLD
|
B&K
DYNA-QUIK
MODEL 500
SOLD
TUBE TESTER
FOR SALE
When you just need a quick,
down, and dirty check on some tubes without flipping a lot of
switches, or you don't have much experience using tube testers. Unit has
new 6AT6 and #83 tubes installed, along with new filter caps. All other
internal components checked and / or replaced where necessary. Tube chart
glued into lid, but sockets have test info for most tubes silk screened
next to them. Has optional 510 expansion module installed. Works and
tests consistent with our calibrated shop B&K 747B. Unit clean. Case
has normal wear to outside covering. Comes with optional 1B3GT socket
adaptor as well as two cap pigtails.
COND. 7.0
SOLD
|
 RCA
MODEL WA-504A
AF GENERATOR
FOR
SALE
Works well w/ exception
of small harmonic tone
occurring around 60 HZ.,
which is typical on a lot of
AF generators due to 60 HZ
line current.
Original knobs and fittings
including handle.
COND. 7.5
HOLD FOR SHOP USE
|
EICO
MODEL 377
FOR
SALE
SERIAL # 17629
AF generator. Scratches on
front visible on photo enlargement. Works fine.
COND. 7.5
HOLD FOR SHOP USE
|
warranty
TENMA
72-320
Dual Trace / 20 Mhz Oscilloscope.
FOR SALE
HOLD FOR SHOP USE |
JACKSON
MODEL 636
TUBE TESTER
SER. # 720
FOR SALE
Very early model based
on such
a low serial
number. Unit does
power up with no
smoke, but untested beyond that. Has internal tube chart. This is an early
tube tester thus is somewhat limited in the tubes it can test. Case scuffed,
but chassis very clean. All pots and switches seem to work. Has original
instructions and original unfilled out warranty card included. Overall
mechanical/ cosmetic condition 7.0
AS IS
ON HOLD FOR SHOP USE
|
B & K
TRANSISTOR RADIO ANALYST
MODEL 960
FOR SALE
Powers up, but we do not have an operations manual so unable to test
further. Selling As-is
SOLD |
(CLICK ABOVE PHOTOS TO ENLARGE)
EICO
MODEL 147
SOLD 4/5/04
Signal Tracer / Test Speaker / Amplifier
FOR SALE
Classic Signal tracer. Works well. Cosmetically a bit challenged. Very clean inside and
out. All tubes and caps checked and replaced where necessary.
Cond. 8.
SOLD 4/5/04
|
 JACKSON MODEL 648
TWEED TUBE TESTER.
COND. 6.0
SOLD
|
HY-TRONIX
AUTOMATIC TRANSISTOR ANALYZER / CHECKER.
MODEL 900
SOLD
|
EMC
MODEL 215
PORTABLE TUBE TESTER
SOLD
|
 EICO
MODEL 635
SOLD
|
EICO
MODEL 625 (BLUE)
SOLD
|
B&K
MODEL 707
SOLD |
Allen & Bradley
1745-PT1
SLC Programmer remote.
SOLD |
HP
4934A TIMS
SOLD |
SUPERIOR
POWER-STAT
TYPE 136B
VARI-AC / DIMMER
FOR SALE
SOLD
|
300 in ONE
ELECTRONICS PROJECT / EXPERIMENTERS KIT
SOLD
|
 RCA
WV-98C
SENIOR VOLT-OHMYST
SOLD
|
HICKOCK / WESTERN ELECTRIC
MODEL KS-15560-L1
TUBE TESTER
Circa 1952
SOLD
|
SYLVANIA
MODEL 220
TUBE TESTER
FOR
SALE
CIRCA 50'S-60'S
CHECKED ALL INTERNAL COMPONENTS. CLEANED CONTACTS, POTS, AND SOCKETS. INSTALLED NEW METER
LAMPS. CHECKED 7 REFERANCE TUBES ( 5U4, 6L6, 6V6, 12AX7, 35W4, 6SJ7, & 50L6)
SATISFACTORILY. METAL CASE AND LID HAVE NO DENTS, OR RUST. SOME "CHEMICAL BURN"
FROM OUT-GASSING OF RUBBER INSULATION ON AC CORD ON FACE NEAR TUBE CHART WINDOWS, AND LID.
VISIBLE AS YELLOWED AREAS. ABBREVIATED INSTRUCTIONS SILK-SCREENED ON LID. TUBE CHART INTACT
AND ROLLS SMOOTH. NO MISSING KNOBS. ALL SWITCHES FUNCTION PROPERLY.
COND. 8.0
SOLD
|
CTI
MODEL TC-20
TUBE TESTER
FOR SALE
Nice portable, very easy to use tube tester by Central Trades Institute.
Has been gone through and has all contacts and controls cleaned. New AC
cord installed. Test results comparable to you shop calibrated B&K
747B. (Tested was 6L6, 5Y3, and 12AX7). Unit is clean with only normal
wear to case. Cap pigtail intact. No cracked or chipped sockets or knobs.
Meter window in great shape! Built-in handle doubles as a leaning stand.
Tube chart, assembly instructions, operating instructions, and schematic
included and fits in rear of unit for storage. No internal tubes required.
Measures 15" wide x 9" tall x 3" deep and weighs only 9lbs
unpacked. Great for portable use!
Cond. 8
SOLD
|
warranty
HEATHKIT
IP-5220
VARI-AC
Variable AC power supply
FOR SALE
These were and are one of the best bench top variable AC power supplies
ever. We have had one for years and would never sell it. This is one we
acquired recently. Everything works well. It has a rough spot on the
voltage control at around 120 volts from being overheated, but still works
and checks fine. The internal lacquer at that spot is blackened, but the
voltage still increases at a steady rate when checked with an analog
voltage meter. It has two amperage ranges, 1 amp and 3 amps. There are
separate, front mounted fuses for both ranges. There are two front mounted
AC outlets. One for Variable and Isolated output from 0-140 VAC. The other
is a non-isolated, fixed 120 (or whatever you are putting in) output. Both
meters work perfectly. This will prove to be one of the most used items on
your work bench.
Cond. 8.5
SOLD
|
(CLICK ABOVE PHOTOS TO ENLARGE)
HEATHKIT
Laboratory Generator
FOR SALE
RF generator. Tests fine. No dents or corrosion. All tubes and caps checked.
Cond. 8.5
SOLD
|
(CLICK ABOVE PHOTOS TO ENLARGE)CONAR
212 VOM
SOLD
|
(CLICK ABOVE PHOTOS TO ENLARGE)
ASTRON
MODEL RS-20A
13.8 VOLT
DC POWER SUPPLY
SOLD 4/5/04
FOR
SALE
Nice 13.8 volt / 20 amp DC power supply. Great for bench work, Mobile
Electronics displays and Amateur Radio Equipment. Very heavy duty binding
post outputs. Features metal cased output rectifiers mounted on heat sink
for years of trouble free service. Heavy duty 3-prong grounded AC cord.
Works perfectly and looks new! Measures 10.5" deep x 9.5" wide x
5.5" tall and weighs 18 lbs unpacked.
Cond. 9
SOLD 4/5/04
|
warranty
VINTAGE RCA
WV-120A
AC (RMS) VOLTAGE
POWER-LINE MONITOR
FOR SALE
A must have for every bench! Continuously monitors your AC power line and
outlets with a large easy to see VU meter. Registers from well less than
100 volts to well over 140 volts. We always have ours plugged in. Great
for monitoring power sags from AC line problems and current hungry loads.
Checked against both our RCA WV-120a and our digital meters. Looks and
works great! Plugs into any standard American AC Edison outlet. Small
footprint measuring only 5 1/8" wide x 4 1/8" high x 3 1/8"
deep. Includes our standard 90 day limited warranty.
Cond. 8.5
SOLD
|
EICO
MODEL 666
DYNAMIC CONDUCTANCE TUBE & TRANSISTOR TESTER
CIRCA 1956
SOLD
|
warranty
B&K
747 B
747B
MUTUAL CONDUCTANCE
TUBE TESTER / CHECKER
SOLID STATE
FOR SALE
Our favorite tester. We have one we have used for years and keep
calibrated. Since it's solid state you don't have to worry that it's
internal tubes have drifted. (Will not test early 4-pin or Acorn style
tubes, but will test all popular and modern (post mid 40's) tubes).
Features include:
- "Jet Check" testing section for very quick testing of select
tubes
- Programmed Testing
- Dynamic Testing
- Tests High Voltage Regulators with proper current (dynamic test injects
a signal voltage into the Grid and another much higher voltage is applied
to the plate at the same time)
- Shorts Test (leakage paths up to 1 megohm and leakage as low as .5
microampere.
- Grid Emission Tests (tests up to 100 megohms)
- Life Test (tests tubes remaining reserve or life expectancy)
- Dual Section testing (Each section of a multi-section tube can be tested
separately)
- Voltage Regulated
- Overload Protection ( Manual circuit breaker protects if an unusually
high load is inserted i.e a shorted tube.)
Very accurate tester. We have completely gone though it doing all
calibrations as follows: 1) Signal Level set 2) Bias Voltage
set 3) Meter Bridge Balance set 4) Shorts
Sensitivity set 5) and finally Grid Emission Sensitivity set.
Meter tests and works great! Exactly as our shop B&K 747B. Includes
both the version II Tube chart (lists over 2500 tubes) and a copy of the
manual / calibration guide. All 30 on board tube sockets in perfect
condition. All controls function perfectly. Meter looks new! Even has
built-in pin straightening for 7 pin miniature, 9 pin miniature, Noval /
magnoval & Decal / Compactron tubes. Tester is built into a
blow-molded heavy duty plastic case. Measures 21" wide x 13"
deep. Includes our standard 90 day limited warranty.
B&K 747B
Cond. 9
SOLD
|
warranty
HEATHKIT / ZENITH
ET-3600
LABORATORY / TRAINER KIT
FOR SALE
These were designed for electronic courses, experimenters, and general
bench use. They are a great multi-purpose device. Features include:
- Onboard 750 hole breadboard
- +1-15 volt low amperage, variable output DC power supply
- -1-15 volt low amperage, variable output DC power supply
- Dual 15 volt low amperage, AC power supplies
- 30 volt low amperage, AC power supply
- 200 Hz- 20 khz Sine Wave generator
- 200 hz - 20 khz Square Wave generator
- 180-1250 ohm general purpose variable potentiometer
- 2.2k-85,000 ohm general purpose variable potentiometer.
- Rear mounted 60-pin ribbon connector
These are great devices. Add a soldering iron and a multi-meter and you
have a great general purpose work-bench. We have completely tested all
functions and all works great! Unit also is in fine cosmetic condition.
Measures 12" wide x 11" deep x 5" tall and weighs 5 lbs.
Comes with our standard 90 day limited warranty.
Cond. 9.5
SOLD
|
RCA
WR-51A
STEREO FM SIGNAL SIMULATOR
CIRCA 1962
SOLD
|
 
Perkins
Model 540A
Automatic Fault Locator
SOLD
|
(CLICK ABOVE PHOTOS TO ENLARGE)
(Click on above thumbnails to
enlarge photos)
HICKOK HICKOCK
752
SOLD TO S.C. 8/22/04
DYNAMIC MUTUAL CONDUCTANCE
TUBE TESTER-CHECKER
FOR SALE
Hickok tube testers are recognized as the more "serious" tube
checkers that were available. Not a good tester for the novice or beginner
to use as they are complicated to operate / utilize to their fullest, but
if you're used to working with tubes / test gear or have a working
knowledge of Hickok's then you will love it. With the exception of the
case (see photo collage) this one is in great shape. We have given it a
"lite" going over, checking internal caps, testing internal
tubes, cleaning contacts, "tweaking" tube chart for easier
rolling and given it a good cleaning overall. We then spot checked a few
different tubes with results consistent with our calibrated
"shop" B&K 747B (747B - easy to use, but no where near the
level of gear the 752 Hickok is). Does include a copy of the manual /
schem in addition to the internal tube chart. Measures 19" x 17"
x 8" (closed" and weighs 23 lbs unpacked.
Hickok 752
Cond. 7.5 (due to case)
As-is
SOLD TO S.C. 8/22/04
|
(Click on above thumbnails to
enlarge photos)
SENCOR
TC142 TC-142
TUBE TESTER / CHECKER
SOLD 4/21/04
FOR SALE
This compact Sencor TC-142
will test most audio, radio &
TV tubes. Good
for simple, easy, and quick tests.
All components checked including the units' internal RCA 12AU7 tube. All
switches cleaned. Comes with original & complete operators manual / tube chart. Tested sample tubes
5Y3, 12AX7 and 6L6 consistent with our calibrated shop B&K 747B. Unit
in usable shape with surface corrosion on face and chrome case parts.
Measures 10.5" x 10.5" x 4.25" and weighs 8 lbs unpacked.
COND. 7
$139.
SOLD 4/21/04
|
Tetronix
551 / 555
O-Scope
SOLD
|
(Click on above thumbnails to
enlarge photos)
HP
HEWLETT PACKARD
MODEL 1220A
OSCILLOSCOPE
SOLD 3/9/05
FOR
SALE
Nice 15-Megahertz, Dual trace O-Scope. We have gone through it checking
for basic function. All functions test fine and trace has been aligned.
Ready to use. Was issued for the French market as silk-screening on front
is in French. Still easy to use and operates like any standard
scope.
-True WORLD AC POWER allows unit
to be operated on 50 or 60 Hz AC (actually ranges from 43-60Hz) and will
select voltages from 110v, 120v, 220v and 240 volts AC input for use
anywhere in the world.
Utilizes standard BNC connector probe(s) (not
included).
Cond. 8.5
SOLD 3/9/05
|
(Click on above thumbnails to
enlarge photos)
GOULD
30 MHz
OSCILLOSCOPE
SOLD TO S.C. 8/30/04
FOR
SALE
Ready to go 30-Megahertz, Dual trace O-Scope. We have gone through it checking
for basic function and cleaning controls internally. All functions test fine.
Ready to use. Measures 17.5" deep x 12.5" wide x 7.5"
tall and weighs 22 lbs unpacked. Utilizes standard BNC connector probe(s) (not
included).
Cond. 8
SOLD TO S.C. 8/30/04
|
|
