(click on above thumbnails to enlarge photos)

AC POWERED!
PHONO / TURNTABLE / CARTRIDGE PRE-AMP
with FREE & CORRECT cables
PREAMP PREAMPLIFIER PRE-AMPLIFIER
for sale
Allows a turntable to be connected to either a modern receiver / pre-amplifier that does not have a phono input (just connect to any Tape, CD, DAT, DVD, AUX or similar input using this phono pre-amp) or allows you to connect your turntable directly to your computer to "Burn" CD's (Computer with audio inputs and a CD burner for this operation). This is a Solid State unit and is AC powered. No batteries to worry about. We have been told by a few customers that have ordered these AC powered units, that they  were replacing their DC (battery) powered units because they were tired of replacing their batteries every couple days. Nice quality unit featuring a full 30Hz-20,000kHz frequency response, 6mV input produces 500mV output, 50K ohm input impedance & Signal to Noise ratio of 60 dB. If you have tried to connect your turntable to your non-phono inputs such as Aux, or a Tape / Video input, and gotten very low, without turning your amp way up, or no volume, YOU NEED THIS! That's just how it works. It also has the proper internal RIAA filtering / EQ'ing to eliminate the "muffled" bass sound you get without one of these. Small package can mounted if preferred to your audio cabinet walls. Standard RCA inputs and outputs and ours ships with either the extra RCA cables or the RCA to Stereo Mini-Plug FREE to connect from the Pre-amp to either your receiver / amp or to your computer. (Specify need at time of purchase) Includes our standard 90 day limited warranty. For Magnetic cartridges.
Phono Pre-Amp
NEW
$29.99 
with correct cables

 

(click on above thumbnails to enlarge photos)
NEW
-THE ULTIMATE-
AUDIO-TECHNICA
AT-440MLa0T
"PURPLE"
1/2" STANDARD MOUNT
TURNTABLE CARTRIDGE
for sale
The Top of the Line in their current Moving Magnet line of high quality turntable cartridges. If you are looking for the best from Audio-Technica here you go. Features "MicroLine" cut Nude Diamond (allows for least record wear and most groove contact) with specially cut Square Shank mounted to a Tapered Alloy tube cantilever. Utilizes Audio-Technicas' own Vector-Aligned dual magnet design for sonic generation. 
Specs are as follows:

- "MicroLine" cut, Nude, Square Shank Diamond  0.12 mil
stylus
- Tapered alloy tube Cantilever
- Frequency Response: 20-20kHz
- Output is a strong 4.0 (mV, 1 kHz, 5 cm/sec)
- Channel Separation; 27 (dB at 1 kHz)
- Channel Balance; 0.8 (dB at 1 KHz)
- Coil impedance : 3,200 ohms at 1 kHz
- Coil inductance (mH, 1 kHz) : 490
- Dynamic compliance (x10-6 cm/dyne) : 10
- Static compliance (x10-6 cm/dyne) : 40
- Dimensions (mm) : L17.3 x W 16.0 x H 28.0
Weight (g) : 6.5
- Recommended Vertical Tracking Force 1.0-1.8 grams (1.4 optimal)
- Recommended loading impedance 47K ohms (standard, requires only standard phono pre-amp built-into most gear).


Again if you are looking for the best sounding cartridge for listening to and especially for recording your vinyl collection and your record collection is in good shape and you want to insure it stays that way this is probably the cartridge for you. Yes it's more expensive than most (although it's not uncommon for cartridges to cost up into the $1000-$2000 range and they can go as high as $15,000), but when compared to the time spent recording, listening to and caring for your albums overtime it's a good and reasonable investment. You won't be disappointed. 
AUDIO-TECHNICA
AT-440MLa0T
NEW
MSRP $300.00

These are official Audio-Technica cartridges.
Not Chinese "bootlegs", "grey-market" or knock-offs like the cheaply priced copies seen all over the internet and in on-line auctions
that simply look like the "real thing".

Our price $189.99
includes "Real-Time, Real-Person" phone support for rebalancing and re-adjusting your tone-arm's user adjustments if required or desired!

 

     

NEW ITEM
(click on above thumbnails to enlarge photos)
NEW
AUDIO-TECHNICA
ATP-2XN0T
PROFESSIONAL / DJ / COMMERCIAL USE
1/2" STANDARD MOUNT
TURNTABLE CARTRIDGE
ALSO FOR PLAYING 78 RPM RECORDS!
COMES WITH AN EXTRA STYLUS TOO!
for sale
Audio Technica's commercial / pro series, Moving Magnet line of high quality turntable cartridges. Designed for any speed records, 16, 45, 33 1/3 or 78 RPM records. This is our only one designed for 78 RPM records. If you are looking for the most durability, or your records aren't in the best shape and you're having a problem tracking heavy enough for some of them, or your table tracks heavy by design, then here you go. Features elliptical cut bonded Diamond (allows for least record wear and most groove contact) with  0.4 x 0.7 cut round Shank mounted to a Super Heavy, Alloy tube cantilever. Utilizes Audio-Technicas' own Vector-Aligned dual magnet design for sonic generation. 
Specs are as follows:

Frequency Response - 15-22,000 Hz
Channel Separation - 23/17 (dB at 1 kHz/10 kHz)
Vertical Tracking Force - 3.0-5.0 grams
Stylus Construction - Bonded round shank
Recommended Load Impedance - 47,000 ohms
Output, a strong 5.3 mV (at 1 kHz, 5 cm/sec)
Channel Balance - 1.5 dB
Stylus Shape - 0.4 x 0.7 mil elliptical
Cantilever - Alloy tube
Mount - Half-inch
Replacement Stylus - ATP-N2 (an extra new one included!)


If you are looking for a cartridge to for DJ or Heavy duty commercial / Professional applications, or your records are a bit "beat" and you need heavy tracking, or you wish to listen to 78's on your "good" table, then this is the cartridge you need. It's made to be abused! Yes it's more expensive than most (although it's not uncommon for cartridges to cost up into the $1000-$2000 range), but when compared to the time spent recording, listening to and caring for your albums overtime it's a good and reasonable investment. You won't be disappointed. 
AUDIO-TECHNICA
ATP-2XN0T
NEW
MSRP $150.00

These are official Audio-Technica cartridges.
Not Chinese "bootlegs", "grey-market" or knock-offs like the cheaply priced copies seen all over the internet and in on-line auctions
that simply look like the "real thing".

Our price $119.99
(with extra new stylus included)
includes "Real-Time, Real-Person" phone support for rebalancing and re-adjusting your tone-arm's user adjustments if required or desired!


 

     

(click on above thumbnails to enlarge photos)
NEW
AUDIO-TECHNICA
AT-120E/T0T
"ORANGE"
1/2" STANDARD MOUNT
TURNTABLE CARTRIDGE
OUR MOST POPULAR MODEL!
for sale
Superior performance in their current Moving Magnet line of high quality turntable cartridges. If you are looking for outstanding performance from Audio-Technica, but still keeping the price under a hundred bucks, then here you go. Features Elliptical cut Nude, 0.3 x 0.7 mil., round shank Diamond mounted to a Alloy tube cantilever. Utilizes Audio-Technicas' own Vector-Aligned dual magnet design for sonic generation. 
Specs are as follows:

- Elliptical Nude Diamond
- Elliptically cut @ 0.3 x 0.7 mil
- Frequency Response: 15-25kHz
- Output is a strong 5 mV @ 1kHz
- Recommended Vertical Tracking Force 1-1.8 grams
- Recommended loading impedance 47K ohms (standard, requires only standard phono pre-amp built-into most gear).


Again if you are looking for an incredible sounding cartridge for listening to and especially for recording your vinyl collection and your record collection is in good shape and you want to insure it stays that way, this is probably the cartridge for you. Yes it's a bit more expensive than many (although it's not uncommon for cartridges to cost up into the $1000-$2000 range), but when compared to the time spent recording, listening to and caring for your albums overtime it's a good and reasonable investment. You won't be disappointed. 
AUDIO-TECHNICA
AT-120E/T0T
NEW
MSRP $160.00

These are official Audio-Technica cartridges.
Not Chinese "bootlegs", "grey-market" or knock-offs like the cheaply priced copies seen all over the internet and in on-line auctions
that simply look like the "real thing".

Our price $89.99
includes "Real-Time, Real-Person" phone support for rebalancing and re-adjusting your tone-arm's user adjustments if required or desired!

90 day full-price upgrade available on this model. *(See below for details)

(click on above thumbnails to enlarge photos)
NEW
AUDIO-TECHNICA
AT311EP AT-311EP0T AT 311EP
UNIVERSAL
1/2" OR P-MOUNT
TURNTABLE CARTRIDGE
for sale
The Audio-Technica AT-311 EP. Will fit turntables requiring either a P-mount or 1/2" standard mount cartridge. A great performing cartridge offering above average performance with-out breaking the bank. Features an Elliptical 0.3 x 0.7 mil Bonded-Diamond stylus for exceptional groove tracking. Utilizes Audio-Technicas' own Vector-Aligned dual magnet design for sonic generation. The AT-311EPOT has a finer elliptical cut to the diamond stylus than it's slightly cheaper counterpart, the AT-301EP / AT301EP and since it has an elliptical cut, will "blow away" the AT300P / AT-300P with it's "Close-n-Play" / Toy style "Conical" cut! At least a good elliptical cut is imperative to accurate sound and lower record wear. Specs are as follows:

- Elliptical Nude Diamond Stylus
- Elliptically cut Bi-Radial @ 0.3 x 0.7 mil
- Frequency Response: 15-27kHz
- Output is a high 5 mV @ 1kHz=
- Thin-Wall Cantilever
- Recommended Vertical Tracking Force 1.0-1.5 grams
- Vertical Tracking Angle 20 °
- Channel Balance = 1.25
- Channel Separation; 29dB @ 1kHz & 18dB @ 10kHz
- Recommended loading impedance 47K ohms (standard, requires only standard phono pre-amp built-into most gear).
- Load Capacitance 100-200 pF


If you are looking for a much above average sounding cartridge for listening and / or recording your vinyl, cartridge then this would make a very nice sounding unit for your 1/2" or P-mount turntable. 
AUDIO-TECHNICA
AT-311EP0T
NEW
MSRP $110.00

These are official Audio-Technica cartridges.
Not Chinese "bootlegs", "grey-market" or knock-offs like the cheaply priced copies seen all over the internet and in on-line auctions
that simply look like the "real thing".

Our price $59.99
includes "Real-Time, Real-Person" phone support for rebalancing and re-adjusting your tone-arm's user adjustments if required or desired!

 

(click on above thumbnails to enlarge photos)
NEW
AUDIO-TECHNICA
  AT-92ECD AT-92ECD0T  AT92ECD
UNIVERSAL
1/2" OR P-MOUNT
TURNTABLE CARTRIDGE
for sale
The Audio-Technica AT-92E. Will fit turntables requiring either a P-mount or standard mount cartridge. Another great performing cartridge offering above average performance with-out breaking the bank. Features a Bonded Elliptical 0.3 x 0.7 mil Diamond stylus for exceptional groove tracking. Utilizes Audio-Technicas' own Vector-Aligned dual magnet design for sonic generation. The AT-92EPOT has a finer elliptical cut to the diamond stylus than it's slightly cheaper counterparts, the AT-301EP / AT301EP and since it has an elliptical cut, will "blow away" the AT300P / AT-300P with it's "Close-n-Play" / Toy style "Conical" cut! At least a good elliptical cut is imperative to accurate sound and lower record wear.
Specs are as follows:

- Frequency Response: 15-27kHz
- Output 3.5 mV @ 1kHz
- Recommended Vertical Tracking Force 1.0-1.5 grams
- Recommended loading impedance 47K ohms (standard, requires only standard phono pre-amp built-into most gear).


If you are looking for an above average sounding cartridge for listening and / or recording your vinyl then this would make a nice sounding cartridge for your 1/2" or P-mount system. 
AUDIO-TECHNICA
AT-92ECD0T
NEW
MSRP $79.

These are official Audio-Technica cartridges.
Not Chinese "bootlegs", "grey-market" or knock-offs like the cheaply priced copies seen all over the internet and in on-line auctions
that simply look like the "real thing".

Our price $44.99

90 day full-price upgrade available on this model. *(See below for details)

 

(click on above thumbnails to enlarge photos)
NEW
AUDIO-TECHNICA
AT-71ELC AT-71ELC0T AT71ELC
"GREEN"
1/2" STANDARD MOUNT
TURNTABLE CARTRIDGE
for sale
The Audio-Technica AT-71ELCOT. Will fit turntables requiring a standard mount cartridge. Another great performing cartridge offering better performance, but keeps the wallet happy. Features a Bonded Elliptical 0.4 x 0.7 mil Diamond stylus for better than average groove tracking. Utilizes Audio-Technicas' own Vector-Aligned dual magnet design for sonic generation. Since the AT-71ELCOT has an elliptically cut diamond stylus it will "blow away" it's slightly cheaper counterparts, the AT70L / AT-70L and CN5625AL (AT-70L is now discontinued anyway) with their "Close-n-Play" / Toy style "Conical" cut stylus'! At least a good elliptical cut is imperative to accurate sound and lower record wear.
Specs are as follows:

- Elliptical Diamond Stylus
- Elliptically cut Bi-Radial @ 0.4 x 0.7 mil
- Frequency Response: 20-22kHz
- Output 3.5 mV ( 1 kHz, 5 cm/sec)
- Channel Separation; 22 (dB at 1 kHz) / 17 (dB at 10 kHz)
- Channel Balance; 1.5 (dB at 1 KHz)
- Recommended Vertical Tracking Force 1.0-2.0 grams
- Recommended loading impedance 47K ohms (standard, requires only standard phono pre-amp built-into most gear).


If you are looking for a decent sounding cartridge for listening to your albums, but not so much  recording and your budget will not bear the cost of the AT-440MLa or the AT-120E/T then this would make a nice sounding cartridge for your 1/2" mount turntable. 
AUDIO-TECHNICA
AT-71ELC0T
NEW
MSRP $80.00

These are official Audio-Technica cartridges.
Not Chinese "bootlegs", "grey-market" or knock-offs like the cheaply priced copies seen all over the internet and in on-line auctions
that simply look like the "real thing".

Our price $49.99
includes "Real-Time, Real-Person" phone support for rebalancing and re-adjusting your tone-arm's user adjustments if required or desired!

90 day full-price upgrade available on this model. *(See below for details)

  

(click on above thumbnails to enlarge photos)
NEW
AUDIO-TECHNICA
AT-3482P0T
P- MOUNT
TURNTABLE CARTRIDGE
for sale
An entry level Audio-Technica AT-3482P. Will fit turntables requiring a "P-mount" cartridge. Definitely keeps a lid on the budget. Features a Bonded Conical 0.7 mil Diamond stylus for tracking and extended record life. Utilizes Audio-Technicas' own Vector-Aligned dual magnet design for sonic generation.
 Specs are as follows:

- Frequency Response: 20-20kHz
- Output strong 5 mV @ 1kHz
- Recommended Vertical Tracking Force 1.0-2.0 grams
- Recommended loading impedance 47K ohms (standard, requires only standard phono pre-amp built-into most gear).


If you are looking for a cartridge for minimal listening to your albums, not recording and your budget will not bear the cost of the above mentioned cartridges then this would make an OK sounding cartridge for your "P" mount turntable. (If you're looking to do much recording "bite the bullet and spend a bit more money for one of the above mentioned cartridges. The quality will be appreciably better and given the amount of time you will invest in your recordings the extra dollars spent at this time will be trivial over time.)
AUDIO-TECHNICA
AT-3482P0T
NEW
MSRP $50.00

These are official Audio-Technica cartridges.
Not Chinese "bootlegs", "grey-market" or knock-offs like the cheaply priced copies seen all over the internet and in on-line auctions
that simply look like the "real thing".

Our price $34.99

 

(click on above thumbnails to enlarge photos)
NEW
AUDIO-TECHNICA
CN5625AL0T
"YELLOW"
1/2" STANDARD MOUNT
TURNTABLE CARTRIDGE
for sale
An entry level Audio-Technica CN5625AL. Will fit turntables requiring a 1/2" standard mount cartridge. Definitely keeps a lid on the budget. Features a Bonded Conical 0.7 mil Diamond stylus for tracking and extended record life. Utilizes Audio-Technicas' own Vector-Aligned dual magnet design for sonic generation. 
Specs are as follows:

- Frequency Response: 20-20kHz
- Output strong 4.2 mV @ 1kHz
- Recommended Vertical Tracking Force 1.0-3.0 grams
- Recommended loading impedance 47K ohms (standard, requires only standard phono pre-amp built-into most gear).


If you are looking for a cartridge for minimal listening to your albums, your speakers or headphones are of questionable quality, your album quality is less than great, you're not recording and your budget will simply not bear the cost of the above mentioned cartridges then this would make an OK sounding cartridge for your standard 1/2" mount turntable. (If you have decent speakers / headphones / vinyl, or you're looking to do much recording "bite the bullet and spend a bit more money for one of the other cartridges on this page, with an "elliptical" diamond stylus as opposed to this "conical" model. The quality will be appreciably better and given the amount of time you will invest in your recordings and listening, the extra dollars spent now will be trivial over time.)
AUDIO-TECHNICA
CN5625AL0T
NEW
MSRP $40.

These are official Audio-Technica cartridges.
Not Chinese "bootlegs", "grey-market" or knock-offs like the cheaply priced copies seen all over the internet and in on-line auctions
that simply look like the "real thing".

Our price $29.99

90 day full-price upgrade available on this model. *(See below for details)

OUR PRIVATE LISTENING / AUDITIONING
SYSTEM